Overclock al mio sistema (Q9550)

[franknos90]

per me.. metti Prime95 test SmallFFT e vediamo se il procio tiene..

[Alex222]

ok provo così, per quanto tempo lo lascio andare?
cmq come ti ho detto mi sa che non regge, anche stamattina si è portato a defoult e ho dovuto risalvare le impostazioni premendo F10... vediamo cosa può essere?

[franknos90]

mi posti seguendo il mio schema tutte le impostazioni che hai adesso?

[Alex222]

Eccolo:

Robust Graphics Booster .................: [Turbo]
CPU Clock Ratio .........................: [8x]
Fine CPU Clock Ratio.....................: [+0.5]
CPU Frequency ...........................: 3.11GHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 366Mhz
PCI Express Frequency (Mhz) .........: [101]
C.I.A. 2.............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mv
PCI Express Clock Drive...................: 900mv
CPU Clock Skew (ps).......................: 0ps
MCH Clock Skew (ps).......................: 0ps
DRAM Performance Control
Performance Enhance....................: [Turbo]
Extreme Memory Profile (X.M.P.)........: [Disabled]
(G)MCH Frequency Latch.................: [Auto]
System Memory Multiplier ..............: 3.00A
Memory Frequency (Mhz) ................: 1098Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time...............................: [5]
tRCD ..........................................: [5]
tRP...........................................: [5]
tRAS...........................................: [15]
Advanced Timing Control [Press Enter]
tRRD...........................................: [Auto]
tWTR...........................................: [Auto]
tWR............................................: [Auto]
tRFC...........................................: [Auto]
tRTP...........................................: [Auto]
Command Rate (CMD) ............................: [Auto]

Motherboard Voltage Control
Load-Line Calibration....................: [Enabled]
CPU Vcore….……….........1.2500V*.........: 1.31250
CPU Termination…...... 1.200V*...........: 1.30
CPU PLL………………….........1.500V*.......... .: 1.50
CPU Reference..........0.760V............: [Normal]
MCH/ICH
MCH Core……………..........1.100V............: 1.26
MCH Reference..…...….….0.760V............: [Auto]
MCH/DRAM Reference.....0.900V............: [Normal]
ICH I/O…………....……......1.50V............: [Normal]
ICH Core...............1.100V............: [Normal]
DRAM
DRAM Voltage ……........1.800V............: 2.00
DRAM Termination ...…..0.900V............: [Normal]
Channel A Address Vref 0.900V............: [Normal]
Channel B Address Vref 0.900V............: [Normal]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect.................: [Enabled]
CPU Enhanced Halt (C1E)...................: [Enabled]
C2/C2E State Support......................: [Disabled]
x C4/C4E State Support....................: [Disabled]
CPU Thermal Monitor 2(TM2) ...............: [Enabled]
CPU EIST Function.........................: [Enabled]
Virtualization Technology.................: [Enabled]

*default


Come puoi vedere, ma mi sono accorto solo ora, che le ultime voci del Advanced settings sono diverse da come mi hai detto di metterle tu... può essere che siano quelle a dare problemi?
altra domanda, sai che le nuove cpu se arrivano a mettiamo 75° si spegono in autoamatico per non arrecare danni al sistema, ecco, non è che mettendo su disabled nelle ultime voci come mi hai detto te, disabilitiamo questa opzione che si spegne da solo? oppure cmq va quella?

Eccoti uno screen:


vorrei sapere, da core temp, mi dice che il VID è a 1,2500, ma quando ero a 3ghz era ancora a 1,2500... come può essere che non sale mai?

grazie aspetto con ansia

[franknos90]

prova a mettere mch reference su normal, dram voltage 2.10 e dram termination a uno step più del normale (tipo 0.910) e cpu vcore a 1,35.. vediam se parte..

[Alex222]

Ho fatto quello che mi hai detto.
Volevo arrivare a 3,6ghz ma con i settaggi che vi ho postato non regge... per ben 2 volte mi è già apparsa la schermata blu di errore e penso sia per il vcore MA NON NE SONO CERRTO!
cosa dici? cosa dovrei sistemare al meglio? grazie


Robust Graphics Booster .................: [Turbo]
CPU Clock Ratio .........................: [8 x]
Fine CPU Clock Ratio.....................: [+0.5]
CPU Frequency ...........................: 3.61GHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 425Mhz
PCI Express Frequency (Mhz) .........: [101]
C.I.A. 2.............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mv
PCI Express Clock Drive...................: 900mv
CPU Clock Skew (ps).......................: 0ps
MCH Clock Skew (ps).......................: 0ps
DRAM Performance Control
Performance Enhance....................: [Turbo]
Extreme Memory Profile (X.M.P.)........: [Disabled]
(G)MCH Frequency Latch.................: [Auto]
System Memory Multiplier ..............: [2.50A]
Memory Frequency (Mhz) ................: 1063Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time...............................: [5]
tRCD ..........................................: [5]
tRP............................................: [5]
tRAS...........................................: [15]
Advanced Timing Control [Press Enter]
tRRD...........................................: [Auto]
tWTR...........................................: [Auto]
tWR............................................: [Auto]
tRFC...........................................: [Auto]
tRTP...........................................: [Auto]
Command Rate (CMD) ............................: [Auto]

Motherboard Voltage Control
Load-Line Calibration....................: [Enabled]
CPU Vcore….……….........1.2500V*..........: 1.35
CPU Termination…...... 1.200V*...........: 1.30
CPU PLL………………….........1.500V*.......... .: 1.50
CPU Reference..........0.760V............: [Normal]
MCH/ICH
MCH Core……………..........1.100V............: 1.26
MCH Reference..…...….….0.760V............: [Normal]
MCH/DRAM Reference.....0.900V............: [Normal]
ICH I/O…………....……......1.50V.............: [Normal]
ICH Core...............1.100V............: [Normal]
DRAM
DRAM Voltage ……........1.800V*............: [2.10V]
DRAM Termination ...…..0.900V*............: [0.920V]
Channel A Address Vref 0.900V............: [Normal]
Channel B Address Vref 0.900V............: [Normal]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect.................: [Disabled]
CPU Enhanced Halt (C1E)...................: [Disabled]
C2/C2E State Support......................: [Disabled]
x C4/C4E State Support....................: [Disabled]
CPU Thermal Monitor 2(TM2) ...............: [Enable]
CPU EIST Function.........................: [Enable]
Virtualization Technology.................: [Disabled]

*default